Online Sale!
100% Guaranteed Genuine Parts
WPW10245259 Whirlpool Terminal Block
The Electric Range Terminal Block is located on the back of your range where the power cord attaches to the appliance. If your appliance is no longer receiving power, replacing this part may alleviate the issue. Note: This part does not include the power cord or mounting hardware. Installing this kit will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: Consider replacing your appliance’s power cord (item PT220) at the same time you make this repair. You may also need the mounting hardware (item WP488130).
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Electric Range Terminal Block
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Electric Range Terminal Block
• Tools Needed: Multi screwdriver
Weight : 0.037500 lbs
Dimension : 3.700700 x 2.755900 x 0.511800
Compatible Brands
About this product
The Electric Range Terminal Block is located on the back of your range where the power cord attaches to the appliance. If your appliance is no longer receiving power, replacing this part may alleviate the issue. Note: This part does not include the power cord or mounting hardware. Installing this kit will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: Consider replacing your appliance’s power cord (item PT220) at the same time you make this repair. You may also need the mounting hardware (item WP488130).
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Electric Range Terminal Block
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Electric Range Terminal Block
• Tools Needed: Multi screwdriver
Weight : 0.037500 lbs
Dimension : 3.700700 x 2.755900 x 0.511800
The following parts are replaced by this product
- 7401P039-60
- 0B00200399
- 1867255
- 550044
- 550834
- 7401P002-60
- 7401P028-60
- 7401P038-60
- 790272
- 4364187
- 8189776
- W10245259
No more associated models for this part.
DIY Instructions on Replacing the WPW10245259 Whirlpool Terminal Block
1. Unplug your dryer from the wall outlet before beginning any repair work.
2. Open up the dryer’s cabinet and locate the WPW10245259 terminal block. This is typically found behind the control panel on the right side of the dryer.
3. Disconnect all the wires attached to the terminal block. Make sure to note where each wire attaches so you can reconnect them later.
4. Remove the two Phillips screws that are securing the terminal block to the dryer's cabinet.
5. Install a new WPW10245259 terminal block in the same spot, ensuring that it lines up correctly with the original mounting holes. Secure it into place with the screw previously removed.
6. Reconnect all the wires to the new terminal block. It is important to make sure the wires are connected to the proper terminals.
7. Once everything has been reassembled, turn on the dryer and test it for proper operation.
With the help of these DIY instructions on replacing the WPW10245259 Whirlpool terminal block, you should be able to do the repair yourself without having to call in a professional. Good luck!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Unplug your dryer from the wall outlet before beginning any repair work.
2. Open up the dryer’s cabinet and locate the WPW10245259 terminal block. This is typically found behind the control panel on the right side of the dryer.
3. Disconnect all the wires attached to the terminal block. Make sure to note where each wire attaches so you can reconnect them later.
4. Remove the two Phillips screws that are securing the terminal block to the dryer's cabinet.
5. Install a new WPW10245259 terminal block in the same spot, ensuring that it lines up correctly with the original mounting holes. Secure it into place with the screw previously removed.
6. Reconnect all the wires to the new terminal block. It is important to make sure the wires are connected to the proper terminals.
7. Once everything has been reassembled, turn on the dryer and test it for proper operation.
With the help of these DIY instructions on replacing the WPW10245259 Whirlpool terminal block, you should be able to do the repair yourself without having to call in a professional. Good luck!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review