WP389140 Whirlpool Drive Block or Bell
The Top Load Washer Drive Block connects to the appliance’s inner wash tub and enables it to spin during the cleaning cycle. If your appliance spins slowly and leaves clothes soaked at the end of the cycle or you hear a loud knocking noise during operation, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drive Block
• Tools Needed: Multi screwdriver, spanner wrench and socket with long extension
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drive Block
• Tools Needed: Multi screwdriver, spanner wrench and socket with long extension
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The Top Load Washer Drive Block connects to the appliance’s inner wash tub and enables it to spin during the cleaning cycle. If your appliance spins slowly and leaves clothes soaked at the end of the cycle or you hear a loud knocking noise during operation, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drive Block
• Tools Needed: Multi screwdriver, spanner wrench and socket with long extension
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Drive Block
• Tools Needed: Multi screwdriver, spanner wrench and socket with long extension
Write Your Own Review
The following parts are replaced by this product
- 389140
- WH40X180
- 357782
- 97360
DIY Guide to Replacing the WP389140 Whirlpool Washer Drive Block 2-5/16 Inch High
This DIY guide to replacing the WP389140 Whirlpool Washer Drive Block 2-5/16 Inch High will enable you to save money on expensive repair costs. By following the instructions provided in this guide, you can perform this repair yourself and have your washer back up and running in no time.
Tools Required:
• Screwdriver
• Pliers
• Socket set
Instructions:
1. Disconnect power to the washer by unplugging the power cord from the wall outlet.
2. Remove the lid of the washer by undoing the screws located at the rear of the machine.
3. Locate the existing WP389140 drive block. This is located near the center of the washer.
4. Gently lift the old drive block out of the machine, being careful not to damage any of the electrical connections or wiring to the unit.
5. Take your new drive block and ensure that all of the electrical connections and wiring are properly connected to the new part.
6. Slide the new drive block into the machine, carefully guiding it underneath the existing wiring harness.
7. Secure the drive block with a couple of screws.
8. Replace the lid to the washer and use a screwdriver to tighten up any screws that may have become loose during the repair process.
9. Re-plug the washer into the wall outlet and turn on the power to the unit.
Congratulations! You have now replaced the WP389140 Whirlpool Washer Drive Block 2-5/16 Inch High.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
This DIY guide to replacing the WP389140 Whirlpool Washer Drive Block 2-5/16 Inch High will enable you to save money on expensive repair costs. By following the instructions provided in this guide, you can perform this repair yourself and have your washer back up and running in no time.
Tools Required:
• Screwdriver
• Pliers
• Socket set
Instructions:
1. Disconnect power to the washer by unplugging the power cord from the wall outlet.
2. Remove the lid of the washer by undoing the screws located at the rear of the machine.
3. Locate the existing WP389140 drive block. This is located near the center of the washer.
4. Gently lift the old drive block out of the machine, being careful not to damage any of the electrical connections or wiring to the unit.
5. Take your new drive block and ensure that all of the electrical connections and wiring are properly connected to the new part.
6. Slide the new drive block into the machine, carefully guiding it underneath the existing wiring harness.
7. Secure the drive block with a couple of screws.
8. Replace the lid to the washer and use a screwdriver to tighten up any screws that may have become loose during the repair process.
9. Re-plug the washer into the wall outlet and turn on the power to the unit.
Congratulations! You have now replaced the WP389140 Whirlpool Washer Drive Block 2-5/16 Inch High.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
