12001541 Whirlpool Dryer Drum Roller Kit
This Dryer Drum Support Roller is what supports the rear of the drum on the dryer. If the appliance is making a loud rumbling or squeaking noise, replacing this part may alleviate the issue. Note that both rollers should be replaced at the same time, and the rollers do not need lubrication. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) roller and (2) washers
• Tools Needed: Snap ring pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) roller and (2) washers
• Tools Needed: Snap ring pliers
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Dryer Drum Support Roller is what supports the rear of the drum on the dryer. If the appliance is making a loud rumbling or squeaking noise, replacing this part may alleviate the issue. Note that both rollers should be replaced at the same time, and the rollers do not need lubrication. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) roller and (2) washers
• Tools Needed: Snap ring pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) roller and (2) washers
• Tools Needed: Snap ring pliers
Write Your Own Review
The following parts are replaced by this product
- 303373
- 303373K
- DE693
- W10116741
- DE693
Replacing the 12001541 Whirlpool Dryer Drum Support Roller Kit with Bearing
Tools Needed:
-Screwdriver
-Pliers
-Safety glasses
Instructions:
1. Unplug the dryer from the wall.
2. On the back of the dryer, remove the screws holding the rear panel in place with a screwdriver. Once all screws are removed, the panel may be pulled away to expose the interior of the dryer.
3. Locate the drum support roller. It is usually located at the top of the dryer drum, near the back wall.
4. Use pliers to remove the old bearing from the roller.
5. Place the new bearing into the roller and secure it with the pliers.
6. Slide the roller into the slot on the back wall of the dryer and replace the screws to secure it in place.
7. Replace the rear panel and tighten all screws.
8. Plug the dryer back into the wall and turn on the power.
9. Test the dryer to make sure the roller is turning properly and that the drum is rotating smoothly.
10. If everything is running properly, the replacement of the 12001541 Whirlpool Dryer Drum Support Roller Kit with Bearing is complete.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Tools Needed:
-Screwdriver
-Pliers
-Safety glasses
Instructions:
1. Unplug the dryer from the wall.
2. On the back of the dryer, remove the screws holding the rear panel in place with a screwdriver. Once all screws are removed, the panel may be pulled away to expose the interior of the dryer.
3. Locate the drum support roller. It is usually located at the top of the dryer drum, near the back wall.
4. Use pliers to remove the old bearing from the roller.
5. Place the new bearing into the roller and secure it with the pliers.
6. Slide the roller into the slot on the back wall of the dryer and replace the screws to secure it in place.
7. Replace the rear panel and tighten all screws.
8. Plug the dryer back into the wall and turn on the power.
9. Test the dryer to make sure the roller is turning properly and that the drum is rotating smoothly.
10. If everything is running properly, the replacement of the 12001541 Whirlpool Dryer Drum Support Roller Kit with Bearing is complete.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
