100% Guaranteed Genuine Parts
STRIKE DOOR-METAL
The D510181 Speed Queen Dryer Metal Door Strike is a genuine OEM (original equipment manufacturer) part that works with Speed Queen, and Amana models of clothes dryers. Please check your model to ensure this part fits prior to ordering.
Weight : 0.007800 lbs
Dimension : 2.677100 x 0.944800 x 0.433000
About this product
The D510181 Speed Queen Dryer Metal Door Strike is a genuine OEM (original equipment manufacturer) part that works with Speed Queen, and Amana models of clothes dryers. Please check your model to ensure this part fits prior to ordering.
Weight : 0.007800 lbs
Dimension : 2.677100 x 0.944800 x 0.433000
The following parts are replaced by this product
- 510181
DIY Replacing the D510181 Speed Queen Dryer Metal Door Strike
Are you experiencing trouble with your Speed Queen dryer? If you notice that the door isn't closing properly due to a damaged or broken metal door strike, take note — this guide will walk you through replacing it. With a few basic tools and the replacement part, you'll be back to drying clothes in no time.
Step 1: Disconnect the Power
Before attempting any repairs, make sure to unplug the dryer from its power source or shut off the circuit breaker. This will help ensure your safety throughout the repair process.
Step 2: Take off the Outer Panel
Open the door of your dryer and unscrew the two screws located at the top of the unit's top panel.
Lift the panel up and remove it, along with the screws. Once the panel is removed, the strike should be visible on the dryer’s frame.
Step 3: Remove the Damaged Strike
The old strike should be easy to remove. It should come off without too much effort. If not, use a combination of pliers and a screwdriver to loosen the screws holding it in place.
Step 4: Replace the Strike
Place the new strike in the appropriate spot. Make sure it is lined up correctly, then secure it in place using the same screws that were holding in the old strike.
Step 5: Reattach the Outer Panel
Replace the outer panel and secure it using the screws you removed earlier. Double-check to make sure everything is secured tightly in order to ensure optimal performance.
Step 6: Test Your Work
Finally, plug the dryer back in and test it out. Open and close the door, and make sure that it is properly secured. If everything checks out, you’re ready to dry another day.
Congratulations! With these easy steps, you’ve successfully replaced your Speed Queen dryer’s metal door strike. With a bit of know-how and some basic tools, you can perform most dryer repairs in your own home. Good luck and happy repairing!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Are you experiencing trouble with your Speed Queen dryer? If you notice that the door isn't closing properly due to a damaged or broken metal door strike, take note — this guide will walk you through replacing it. With a few basic tools and the replacement part, you'll be back to drying clothes in no time.
Step 1: Disconnect the Power
Before attempting any repairs, make sure to unplug the dryer from its power source or shut off the circuit breaker. This will help ensure your safety throughout the repair process.
Step 2: Take off the Outer Panel
Open the door of your dryer and unscrew the two screws located at the top of the unit's top panel.
Lift the panel up and remove it, along with the screws. Once the panel is removed, the strike should be visible on the dryer’s frame.
Step 3: Remove the Damaged Strike
The old strike should be easy to remove. It should come off without too much effort. If not, use a combination of pliers and a screwdriver to loosen the screws holding it in place.
Step 4: Replace the Strike
Place the new strike in the appropriate spot. Make sure it is lined up correctly, then secure it in place using the same screws that were holding in the old strike.
Step 5: Reattach the Outer Panel
Replace the outer panel and secure it using the screws you removed earlier. Double-check to make sure everything is secured tightly in order to ensure optimal performance.
Step 6: Test Your Work
Finally, plug the dryer back in and test it out. Open and close the door, and make sure that it is properly secured. If everything checks out, you’re ready to dry another day.
Congratulations! With these easy steps, you’ve successfully replaced your Speed Queen dryer’s metal door strike. With a bit of know-how and some basic tools, you can perform most dryer repairs in your own home. Good luck and happy repairing!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review