100% Guaranteed Genuine Parts
D511255P Speed Queen Dryer Cylinder Belt Rubber Face
Cylinder belt - rubber face works with some Speed Queen, and Amana models of clothes dryers.
Weight : 0.106900 lbs
Dimension : 6.650000 x 5.160000 x 0.430000
About this product
Cylinder belt - rubber face works with some Speed Queen, and Amana models of clothes dryers.
Weight : 0.106900 lbs
Dimension : 6.650000 x 5.160000 x 0.430000
The following parts are replaced by this product
- 511255
- 511255
- 510178
- 511255P
Step 1: Unplug the Dryer
Before beginning any repair on a Speed Queen dryer, it is important to make sure that the appliance is unplugged from its wall outlet and the power switch is turned off. This will help to prevent any electrical shocks or malfunctions during the repair.
Step 2: Remove the Top of the Dryer
In order to access the inner workings of the dryer, you will need to remove the top panel. This can be done by unscrewing the two screws located at the back corners of the top of the dryer. With the screws removed, you can carefully lift the lid off and set it aside.
Step 3: Locating the Cylinder Belt - Rubber Face
Using a flashlight, look around the inside of the dryer and locate the cylinder belt. This is the rubber belt that helps to turn the drum inside the dryer. The belt should be visible near the center of the dryer, connected to the pulley wheel.
Step 4: Removing the Old Cylinder Belt - Rubber Face
Once you have found the old belt, use a flathead screwdriver to gently pry it away from the pulley wheel, making sure not to damage the pulley itself. Once the belt is removed, you can discard it and begin preparing the new belt.
Step 5: Installing the New Cylinder Belt - Rubber Face
You will now need to install the new cylinder belt - rubber face. To do this, simply feed the belt around the pulley wheel and start to tighten it until it is secure. You can then use the flathead screwdriver to ensure that the belt is properly fitted and tightened.
Step 6: Reassemble the Dryer
Once the new belt is installed, you can begin reassembling the dryer. Replace the top lid, screw it in place and then plug the dryer back into its wall outlet. You can then turn on the power switch and test to ensure that it works normally.
Step 7: Enjoy the Benefits of a Replaced Cylinder Belt - Rubber Face
Congratulations! You have successfully replaced the D511255P Speed Queen dryer's cylinder belt - rubber face. Enjoy the benefits that come with a well-functioning dryer and enjoy safe and efficient operation for years to come.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Before beginning any repair on a Speed Queen dryer, it is important to make sure that the appliance is unplugged from its wall outlet and the power switch is turned off. This will help to prevent any electrical shocks or malfunctions during the repair.
Step 2: Remove the Top of the Dryer
In order to access the inner workings of the dryer, you will need to remove the top panel. This can be done by unscrewing the two screws located at the back corners of the top of the dryer. With the screws removed, you can carefully lift the lid off and set it aside.
Step 3: Locating the Cylinder Belt - Rubber Face
Using a flashlight, look around the inside of the dryer and locate the cylinder belt. This is the rubber belt that helps to turn the drum inside the dryer. The belt should be visible near the center of the dryer, connected to the pulley wheel.
Step 4: Removing the Old Cylinder Belt - Rubber Face
Once you have found the old belt, use a flathead screwdriver to gently pry it away from the pulley wheel, making sure not to damage the pulley itself. Once the belt is removed, you can discard it and begin preparing the new belt.
Step 5: Installing the New Cylinder Belt - Rubber Face
You will now need to install the new cylinder belt - rubber face. To do this, simply feed the belt around the pulley wheel and start to tighten it until it is secure. You can then use the flathead screwdriver to ensure that the belt is properly fitted and tightened.
Step 6: Reassemble the Dryer
Once the new belt is installed, you can begin reassembling the dryer. Replace the top lid, screw it in place and then plug the dryer back into its wall outlet. You can then turn on the power switch and test to ensure that it works normally.
Step 7: Enjoy the Benefits of a Replaced Cylinder Belt - Rubber Face
Congratulations! You have successfully replaced the D511255P Speed Queen dryer's cylinder belt - rubber face. Enjoy the benefits that come with a well-functioning dryer and enjoy safe and efficient operation for years to come.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review