Online Sale!
100% Guaranteed Genuine Parts
WP2196100 Whirlpool Shelf Retainer Bar Support
The Refrigerator Door Shelf Retainer Bar End Cap connects to the retainer bar on your refrigerator’s door shelf, and attaches it to the refrigerator door. If your shelf retainer bar has become disconnected, a damaged end cap could be the cause. To remove the end cap, first unhook the release tab on both ends of the retainer bar. Slide out the bar and the end caps, and slide out the defective cap. Now, simply replace the end cap and snap the bar with end caps back in place on the refrigerator door. This part is made of white plastic and is sold individually. Installation will require basic hand tools, minor disassembly of the unit and novice repair experience.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Door Shelf Retainer Bar End Cap
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Door Shelf Retainer Bar End Cap
• Tools Needed: Multi screwdriver
Weight : 0.064700 lbs
Dimension : 3.120000 x 2.620000 x 1.120000
Compatible Brands
About this product
The Refrigerator Door Shelf Retainer Bar End Cap connects to the retainer bar on your refrigerator’s door shelf, and attaches it to the refrigerator door. If your shelf retainer bar has become disconnected, a damaged end cap could be the cause. To remove the end cap, first unhook the release tab on both ends of the retainer bar. Slide out the bar and the end caps, and slide out the defective cap. Now, simply replace the end cap and snap the bar with end caps back in place on the refrigerator door. This part is made of white plastic and is sold individually. Installation will require basic hand tools, minor disassembly of the unit and novice repair experience.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Door Shelf Retainer Bar End Cap
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Door Shelf Retainer Bar End Cap
• Tools Needed: Multi screwdriver
Weight : 0.064700 lbs
Dimension : 3.120000 x 2.620000 x 1.120000
The following parts are replaced by this product
- 2196100
- 1110719
- 1124441
- 2148029
No more associated models for this part.
Replacing the Whirlpool WP2196100 ENDCAP-TRM
1. Shut off power to the dryer before performing any maintenance tasks.
2. Unplug the dryer from the wall outlet and disconnect the vent line from the dryer.
3. Remove any screws holding the top panel in place and lift it up to gain access to the interior of the dryer.
4. Locate the endcap-trm, which is located near the back of the interior of the dryer.
5. Disconnect the wiring harness connected to the endcap-trm.
6. Use a screwdriver to remove the four screws that secure the endcap-trm in place.
7. Pull out the old endcap-trm and set it aside.
8. Take the new endcap-trm and secure it in place with the four screws.
9. Reconnect the wiring harness to the new endcap-trm.
10. Replace the top panel and reattach any screws that were removed.
11. Carefully reroute the vent line to the dryer and plug the dryer into the wall outlet.
12. Turn the power back on and test the dryer to make sure it’s working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Shut off power to the dryer before performing any maintenance tasks.
2. Unplug the dryer from the wall outlet and disconnect the vent line from the dryer.
3. Remove any screws holding the top panel in place and lift it up to gain access to the interior of the dryer.
4. Locate the endcap-trm, which is located near the back of the interior of the dryer.
5. Disconnect the wiring harness connected to the endcap-trm.
6. Use a screwdriver to remove the four screws that secure the endcap-trm in place.
7. Pull out the old endcap-trm and set it aside.
8. Take the new endcap-trm and secure it in place with the four screws.
9. Reconnect the wiring harness to the new endcap-trm.
10. Replace the top panel and reattach any screws that were removed.
11. Carefully reroute the vent line to the dryer and plug the dryer into the wall outlet.
12. Turn the power back on and test the dryer to make sure it’s working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review