WP3979346 Whirlpool Water Inlet Valve
This Top Load Washer Water Inlet Valve opens to allow water to enter the washing machine. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer won't stop filling with water, won't produce cold or hot water, won't fill at all, or is leaking, replacing the inlet valve may alleviate these issues.This inlet valve has 4 terminals and is located at the back of the machine. To access the part, you'll need to separate the washer cabinet from the washer and disconnect the red and white wiring connectors from the old part. Recommended Item: Washer Fill Hose (item 8212487RP). Package of two 5' industrial braid hoses with pre-installed washers and straight ends. We recommend replacing washing machine inlet hoses after 5 years of use to reduce the risk of hose failure. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Water Inlet Valve Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Water Inlet Valve Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Top Load Washer Water Inlet Valve opens to allow water to enter the washing machine. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer won't stop filling with water, won't produce cold or hot water, won't fill at all, or is leaking, replacing the inlet valve may alleviate these issues.This inlet valve has 4 terminals and is located at the back of the machine. To access the part, you'll need to separate the washer cabinet from the washer and disconnect the red and white wiring connectors from the old part. Recommended Item: Washer Fill Hose (item 8212487RP). Package of two 5' industrial braid hoses with pre-installed washers and straight ends. We recommend replacing washing machine inlet hoses after 5 years of use to reduce the risk of hose failure. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Water Inlet Valve Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Top Load Washer Water Inlet Valve Assembly
• Tools Needed: Multi screwdriver, needle-nose pliers
Write Your Own Review
The following parts are replaced by this product
- 3979346
- 3979347
DIY Instructions for Replacing a WP3979346 Whirlpool Water Inlet Valve
Replacing your Whirlpool water inlet valve (WP3979346) isn’t difficult, and it can save you money by avoiding a costly service call. Follow these steps to get the job done:
1. Gather Your Tools and Materials – Before you start, make sure you have all the necessary tools and materials on hand. You’ll need a Phillips screwdriver, pliers, duct tape, wire cutters, and an exact replacement valve for your washer.
2. Shut Off the Water Supply – Unscrew the two screws holding the face plate on the wall, then shut off the water supply to the washer. You may need to shut off the main water valve if no individual one is available.
3. Disconnect the Hoses – Carefully disconnect each of the hoses attached to the existing water inlet valve. Make sure you label each hose so that you can reconnect them to the right one.
4. Remove Old Inlet Valve – Detach the mounting bracket from the wall using your Phillips screwdriver. Once it’s loose, pull the valve out and discard it.
5. Install New Inlet Valve – Position the new valve in the same place as the old one, then reattach the mounting bracket. Connect the water supply lines, making sure that they are tightened securely.
6. Test New Valve – Turn the water supply back on and check for any leaks. If there are none, test the new valve by running the washer. Once everything is working properly, you’re good to go!
Changing a Whirlpool water inlet valve (WP3979346) doesn’t have to be a hassle. With the right tools, following these instructions will get you back to doing laundry in no time.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Replacing your Whirlpool water inlet valve (WP3979346) isn’t difficult, and it can save you money by avoiding a costly service call. Follow these steps to get the job done:
1. Gather Your Tools and Materials – Before you start, make sure you have all the necessary tools and materials on hand. You’ll need a Phillips screwdriver, pliers, duct tape, wire cutters, and an exact replacement valve for your washer.
2. Shut Off the Water Supply – Unscrew the two screws holding the face plate on the wall, then shut off the water supply to the washer. You may need to shut off the main water valve if no individual one is available.
3. Disconnect the Hoses – Carefully disconnect each of the hoses attached to the existing water inlet valve. Make sure you label each hose so that you can reconnect them to the right one.
4. Remove Old Inlet Valve – Detach the mounting bracket from the wall using your Phillips screwdriver. Once it’s loose, pull the valve out and discard it.
5. Install New Inlet Valve – Position the new valve in the same place as the old one, then reattach the mounting bracket. Connect the water supply lines, making sure that they are tightened securely.
6. Test New Valve – Turn the water supply back on and check for any leaks. If there are none, test the new valve by running the washer. Once everything is working properly, you’re good to go!
Changing a Whirlpool water inlet valve (WP3979346) doesn’t have to be a hassle. With the right tools, following these instructions will get you back to doing laundry in no time.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
