WP12656105 Whirlpool Drawer Support
The SxS Refrigerator Pantry Drawer Support Track, Left Side not only supports the drawer for your appliance, but also supports the drawer door and the glass shelf sitting on top of the drawer. To replace the current track, pull out the pantry drawer inside of the refrigerator, and then push the door of the drawer to the right. Use your finger to press on the left hinge of the door and release it. Remove the crisper drawers, the glass shelf, and the front and rear glass support. Then remove the pantry drawer and use a 1/4" nut driver to remove the screws holding in the current support track. You'll remove the old rail and attach it to the new support track. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Refrigerator Pantry Drawer Endcap (item WP12656018) for the right side.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) SxS Refrigerator Pantry Drawer Support Track, Left Side
• Tools Needed: 1/4" nut driver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) SxS Refrigerator Pantry Drawer Support Track, Left Side
• Tools Needed: 1/4" nut driver
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The SxS Refrigerator Pantry Drawer Support Track, Left Side not only supports the drawer for your appliance, but also supports the drawer door and the glass shelf sitting on top of the drawer. To replace the current track, pull out the pantry drawer inside of the refrigerator, and then push the door of the drawer to the right. Use your finger to press on the left hinge of the door and release it. Remove the crisper drawers, the glass shelf, and the front and rear glass support. Then remove the pantry drawer and use a 1/4" nut driver to remove the screws holding in the current support track. You'll remove the old rail and attach it to the new support track. Replacing this part will require basic hand tools, some disassembly of the refrigerator and novice repair experience. You must unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Refrigerator Pantry Drawer Endcap (item WP12656018) for the right side.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) SxS Refrigerator Pantry Drawer Support Track, Left Side
• Tools Needed: 1/4" nut driver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) SxS Refrigerator Pantry Drawer Support Track, Left Side
• Tools Needed: 1/4" nut driver
Write Your Own Review
The following parts are replaced by this product
- 67002326
- 8171058
- 67005862
- 12656105
DIY Instructions for Replacing a WP12656105 Whirlpool End Cap Kit
1. Prepare the area where you will be replacing the end cap kit with a clean workspace and adequate lighting. Make sure to unplug the power cord from any electrical outlet.
2. Locate the existing end cap kit and remove all the screws holding it in place. Carefully pull out the end cap from the unit to avoid damaging any other parts.
3. Take your new WP12656105 Whirlpool End Cap Kit and align the mounting holes with the holes in the unit. Secure the end cap using the provided screws.
4. Reconnect the power cord and test the unit to make sure it is operating correctly.
5. Check for leaks around the new end cap. If there are no leaks, you have successfully replaced the Whirlpool End Cap Kit.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Prepare the area where you will be replacing the end cap kit with a clean workspace and adequate lighting. Make sure to unplug the power cord from any electrical outlet.
2. Locate the existing end cap kit and remove all the screws holding it in place. Carefully pull out the end cap from the unit to avoid damaging any other parts.
3. Take your new WP12656105 Whirlpool End Cap Kit and align the mounting holes with the holes in the unit. Secure the end cap using the provided screws.
4. Reconnect the power cord and test the unit to make sure it is operating correctly.
5. Check for leaks around the new end cap. If there are no leaks, you have successfully replaced the Whirlpool End Cap Kit.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
