Whirlpool Appliance Sensor & Thermistor

The Whirlpool Dryer Thermistor is located on the blower housing next to the thermal fuse. If your appliance's drying cycle is too long or too short, or if your appliance is di ...splaying a fault code, replacing this part may alleviate these issues. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Thermistor• Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. The oven temperatu ...re may be inaccurate by more than 50 degrees Fahrenheit. The sensor is usually located at the back of your oven, held in place by several screws and a wiring harness. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Ice Maker Thermistor monitors the temperature inside the appliance and sends the reading to the electronic control board. If your ice maker is making too much ice and caus ...ing the bin to overflow, replacing this part may alleviate this issue. Installing this part will require basic hand tools, some disassembly of the ice makerand novice repair experience. You must unplug the ice maker or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Ice Maker Thermistor• Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This Dual Oven Sensor monitors the temperature inside the lower oven compartment and relays the information to the main control board. If your lower oven isn’t heating prope ...rly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dual Oven Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Whirlpool WPW10384183 THERMISTOR is a genuine OEM part. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other applian ...ce parts needs! Read More Read Less

The Oven Temperature Sensor measures the oven temperature and sends the information to the electronic control. If your oven isn't holding the correct temperature, replacing th ...is part may alleviate the issue. This sensor measures just over 3" L and is located inside the back panel of the range. Note that you may need assistance removing the appliance to complete this repair. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Oven Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This Top Load Washer Rotor Position Sensor communicates the position of the tub’s rotor to the control board during the washing cycle. If the appliance's motor isn’t worki ...ng properly to spin the wash tub, or your washer displays an error message, replacing the rotor position sensor may alleviate these issues. To access the part, tilt the washer back letting it rest on something to support it and tape the lid down. You'll need to remove the rotor and rotor stator at the bottom of the machine. The sensor is attached to the top of the stator. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Rotor Position Sensor• Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

This Refrigerator Temperature Sensor senses the temperature inside the refrigerator and sends information to the electronic control so temperature stays regulated. If your app ...liance's temperature isn't consistent, replacing the sensor may alleviate this issue. To access this part, open the refrigerator door and locate the thermistor cover on the side wall of your appliance. Remove all shelves from the refrigerator and then remove the thermistor from the cover. Using side cutters, cut the thermistor wires at the base of the thermistor and discard the old part. You'll then pull the wires apart in the new thermistor and insert them into the old IDC splice connector. We strongly recommend that you hire a qualified technician to safely install this part. Replacing this part will require advanced mechanical training. Specialized tools, complex testing and appliance calibration may be required.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Temperature Sensor• Tools Needed: Specialized Tools Read More Read Less

The Gas Dryer Flame Sensor reacts to the heat from the ignitor, allowing the gas valve to open and the dryer to create heat. If your appliance isn't heating as expected during ... operation, replacing this part may alleviate the issue. This sensor is located across from the gas igniter at the dryer’s burner assembly and should be closed for continuity at room temperature. Be sure to check for continuity with a multimeter before installing a new sensor. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Item: While the dryer is disassembled, consider replacing the gas valve coils (item 279834) as well.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Dryer Flame Sensor• Tools Needed: Multi screwdriver Read More Read Less