W10316760 Whirlpool Thermistor Kit
This Refrigerator Temperature Sensor senses the temperature inside the refrigerator and sends information to the electronic control so temperature stays regulated. If your appliance's temperature isn't consistent, replacing the sensor may alleviate this issue. To access this part, open the refrigerator door and locate the thermistor cover on the side wall of your appliance. Remove all shelves from the refrigerator and then remove the thermistor from the cover. Using side cutters, cut the thermistor wires at the base of the thermistor and discard the old part. You'll then pull the wires apart in the new thermistor and insert them into the old IDC splice connector. We strongly recommend that you hire a qualified technician to safely install this part. Replacing this part will require advanced mechanical training. Specialized tools, complex testing and appliance calibration may be required.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Temperature Sensor
• Tools Needed: Specialized Tools
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Temperature Sensor
• Tools Needed: Specialized Tools
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
This Refrigerator Temperature Sensor senses the temperature inside the refrigerator and sends information to the electronic control so temperature stays regulated. If your appliance's temperature isn't consistent, replacing the sensor may alleviate this issue. To access this part, open the refrigerator door and locate the thermistor cover on the side wall of your appliance. Remove all shelves from the refrigerator and then remove the thermistor from the cover. Using side cutters, cut the thermistor wires at the base of the thermistor and discard the old part. You'll then pull the wires apart in the new thermistor and insert them into the old IDC splice connector. We strongly recommend that you hire a qualified technician to safely install this part. Replacing this part will require advanced mechanical training. Specialized tools, complex testing and appliance calibration may be required.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Temperature Sensor
• Tools Needed: Specialized Tools
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Refrigerator Temperature Sensor
• Tools Needed: Specialized Tools
Write Your Own Review
The following parts are replaced by this product
- 12791417SP
- W10323459
- WPW10323459
- 12791419SP
Replacing the Whirlpool W10316760 Thermistor
1. Unplug the appliance from the power source and turn off the water supply if applicable.
2. Open the appliance and locate the thermistor. It should be near the heating element.
3. Disconnect any wires attached to the thermistor.
4. Remove the thermistor by carefully pulling it out of its housing.
5. Compare the old thermistor with the new one to make sure they match.
6. Insert the new thermistor into its housing and reattach the wires.
7. Reassemble the appliance and reconnect it to the power source and turn on the water supply if applicable.
8. Test the appliance to make sure the new thermistor is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Unplug the appliance from the power source and turn off the water supply if applicable.
2. Open the appliance and locate the thermistor. It should be near the heating element.
3. Disconnect any wires attached to the thermistor.
4. Remove the thermistor by carefully pulling it out of its housing.
5. Compare the old thermistor with the new one to make sure they match.
6. Insert the new thermistor into its housing and reattach the wires.
7. Reassemble the appliance and reconnect it to the power source and turn on the water supply if applicable.
8. Test the appliance to make sure the new thermistor is working properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
