Whirlpool Appliance Range Parts Sensor & Thermistor

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. The oven temperatu ...re may be inaccurate by more than 50 degrees Fahrenheit. The sensor is usually located at the back of your oven, held in place by several screws and a wiring harness. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This Dual Oven Sensor monitors the temperature inside the lower oven compartment and relays the information to the main control board. If your lower oven isn’t heating prope ...rly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dual Oven Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Oven Temperature Sensor measures the oven temperature and sends the information to the electronic control. If your oven isn't holding the correct temperature, replacing th ...is part may alleviate the issue. This sensor measures just over 3" L and is located inside the back panel of the range. Note that you may need assistance removing the appliance to complete this repair. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Oven Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing the sensor may alleviate this issue. This sensor repl ...aces many long tipped oven sensors and includes instructions and additional plugs to replace the original. To access the part, take the access panel off the back of the range and set it aside. Disconnect the sensor's wiring harness at the back of the oven. Then open the oven door, remove the racks, and remove the screws at the back of the oven holding the sensor in. This kit includes (2) adapters if needed. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor Kit• Tools Needed: Phillips-Head screwdriver Read More Read Less

The Range Meat Probe Sensor is used to measure the internal temperature of meat during cooking, allowing the oven to maintain a more accurate temperature. If the existing prob ...e is missing or no longer functioning properly, reapacing it may alleviate the issue. Installing the sensor will not require any tools, disassembly or repair experience. Simply plug the probe into the jack in the right side of the oven and insert the probe into the food item during cooking.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Meat Probe Sensor• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Electric Range Temperature Sensor measures the oven temperature and sends the information to the electronic control. If your oven isn't holding the correct temperature, th ...e sensor has most likely failed and needs to be replaced. This sensor measures just over 3-in length and is located inside the back panel of the range. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

W11208292 is an original equipment manufactured (OEM) part. Enhance your microwave's performance with this high-quality sensor and thermistor from a trusted brand. Designed fo ...r a variety of compatible brands, including Admiral, Amana, Jenn-Air, Kenmore, Kitchenaid, Magic Chef, Maytag, Norge, Roper, and Whirlpool, this component ensures accurate temperature readings and improved cooking efficiency. Built to meet stringent standards, it helps to prevent overheating and ensures your meals are cooked evenly. Installing this part is straightforward, making it an ideal option for DIY repairs. Whether you're upgrading an existing microwave or replacing a worn-out sensor, this durable and reliable component supports optimal functionality. Ensure your cooking appliance performs at its best, providing you with the quality and convenience you expect. Read More Read Less