279816 Whirlpool Dryer Thermal Cut Off Fuse Kit
The Dryer Thermal Fuse Kit includes (1) jumper wire, (3) screws, (2) connectors, installation instructions, (1) hi-limit thermostat and (1) thermal cut-off. The thermal fuse is located on the blower housing and shuts off the heating element when the dryer overheats. If your dryer won't start or will run but not heat up, replacing this part may alleviate these issues. Note that the thermal fuse cannot be reset. A clogged dryer vent is the most common cause for a blown thermal fuse. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Thermal Fuse Kit
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Thermal Fuse Kit
• Tools Needed: Multi screwdriver
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
The Dryer Thermal Fuse Kit includes (1) jumper wire, (3) screws, (2) connectors, installation instructions, (1) hi-limit thermostat and (1) thermal cut-off. The thermal fuse is located on the blower housing and shuts off the heating element when the dryer overheats. If your dryer won't start or will run but not heat up, replacing this part may alleviate these issues. Note that the thermal fuse cannot be reset. A clogged dryer vent is the most common cause for a blown thermal fuse. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Thermal Fuse Kit
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Dryer Thermal Fuse Kit
• Tools Needed: Multi screwdriver
Write Your Own Review
The following parts are replaced by this product
- 3399848
- 3977393
- 279816VP
Step 1: Unplug the dryer's power cord from the wall outlet. Use a screwdriver to remove the back panel of the dryer and locate the existing thermal cut-off fuse kit.
Step 2: Using needle nose pliers, carefully pull out the two wires from the terminal block of the thermal cut-off fuse kit.
Step 3: Insert the new 279816 Whirlpool Dryer Thermal Cut-Off Fuse Kit into the terminal block. Secure the wires by twisting them around the screws and push the screws into their holes.
Step 4: Place the original faceplate onto the new 279816 Whirlpool Dryer Thermal Cut-Off Fuse Kit.
Step 5: Secure the back panel to the dryer and plug in the power cord.
Step 6: Test the dryer to make sure it is running properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Step 2: Using needle nose pliers, carefully pull out the two wires from the terminal block of the thermal cut-off fuse kit.
Step 3: Insert the new 279816 Whirlpool Dryer Thermal Cut-Off Fuse Kit into the terminal block. Secure the wires by twisting them around the screws and push the screws into their holes.
Step 4: Place the original faceplate onto the new 279816 Whirlpool Dryer Thermal Cut-Off Fuse Kit.
Step 5: Secure the back panel to the dryer and plug in the power cord.
Step 6: Test the dryer to make sure it is running properly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
