Online Sale!
100% Guaranteed Genuine Parts
WP53-0918 Whirlpool Lint Filter
The Front Load Dryer Lint Screen is a white screen that provides proper air flow and operation of your dryer. After pulling the old filter out, be sure to clean the channels of the lint housing before inserting the new lint screen.The filter should be cleaned before every load of laundry and replaced immediately if damaged. This a replacement lint filter with handle measures approximately 3/8" thick on the left side and 5/8" thick on the right side. Replacing your dryer’s lint filter is a quick and essential way to keep your appliance operating at optimal levels. Installing this part requires no tools, disassembly or repair experience. Recommended Tool: The Cleaning Brush (item 4210463RW) is useful to remove lint and other debris from the dryer’s venting.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Front Load Dryer Lint Screen
• No tools required for installation
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Front Load Dryer Lint Screen
• No tools required for installation
Weight : 0.755400 lbs
Dimension : 14.750000 x 6.500000 x 1.250000
Compatible Brands
About this product
The Front Load Dryer Lint Screen is a white screen that provides proper air flow and operation of your dryer. After pulling the old filter out, be sure to clean the channels of the lint housing before inserting the new lint screen.The filter should be cleaned before every load of laundry and replaced immediately if damaged. This a replacement lint filter with handle measures approximately 3/8" thick on the left side and 5/8" thick on the right side. Replacing your dryer’s lint filter is a quick and essential way to keep your appliance operating at optimal levels. Installing this part requires no tools, disassembly or repair experience. Recommended Tool: The Cleaning Brush (item 4210463RW) is useful to remove lint and other debris from the dryer’s venting.
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Front Load Dryer Lint Screen
• No tools required for installation
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Front Load Dryer Lint Screen
• No tools required for installation
Weight : 0.755400 lbs
Dimension : 14.750000 x 6.500000 x 1.250000
The following parts are replaced by this product
- 53-0918
- ER53-0918
No more associated models for this part.
Replacing the Whirlpool WP53-0918 FILTER-LIQUID
Are you looking to replace your Whirlpool WP53-0918 FILTER-LIQUID? Here is a comprehensive step-by-step guide to replacing this filter.
Step One: Gather Necessary Supplies
Before you begin, make sure you have all the necessary supplies on hand. You'll need the new Whirlpool WP53-0918 FILTER-LIQUID, replacement O-rings, adjustable wrench and pliers (or a strap wrench).
Step Two: Turn off the Water Supply
Before you start any work, it is important that you shut off the water supply. This will ensure that you don't get water everywhere while you are attempting to remove the old filter.
Step Three: Remove Old Filter
Using your adjustable wrench, carefully unscrew the old filter from the inlet side of the filter housing. Be sure to be gentle, as this could cause leaks if you aren't careful. Once the old filter has been removed, use pliers or a strap wrench to remove the O-ring that was used to secure it.
Step Four: Install New Filter
Now it's time to install the new filter. First, put the O-ring back onto the inlet side of the filter housing. Then, place the new filter into the housing and secure it with the adjustable wrench. Make sure that it is snug and that there are no leaks.
Step Five: Check for Leaks
Once the new filter is installed, turn the water back on and check for any leaks. Be sure to monitor it for at least 10 minutes. If you detect any water leaking from either side of the filter, shut off the water again and try to tighten the connections until the leak stops.
Step Six: Enjoy Fresh Water
Once you've checked for leaks and everything appears to be in order, you can turn the water back on and enjoy fresh filtered water. Congratulations - you've successfully replaced your Whirlpool WP53-0918 FILTER-LIQUID!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Are you looking to replace your Whirlpool WP53-0918 FILTER-LIQUID? Here is a comprehensive step-by-step guide to replacing this filter.
Step One: Gather Necessary Supplies
Before you begin, make sure you have all the necessary supplies on hand. You'll need the new Whirlpool WP53-0918 FILTER-LIQUID, replacement O-rings, adjustable wrench and pliers (or a strap wrench).
Step Two: Turn off the Water Supply
Before you start any work, it is important that you shut off the water supply. This will ensure that you don't get water everywhere while you are attempting to remove the old filter.
Step Three: Remove Old Filter
Using your adjustable wrench, carefully unscrew the old filter from the inlet side of the filter housing. Be sure to be gentle, as this could cause leaks if you aren't careful. Once the old filter has been removed, use pliers or a strap wrench to remove the O-ring that was used to secure it.
Step Four: Install New Filter
Now it's time to install the new filter. First, put the O-ring back onto the inlet side of the filter housing. Then, place the new filter into the housing and secure it with the adjustable wrench. Make sure that it is snug and that there are no leaks.
Step Five: Check for Leaks
Once the new filter is installed, turn the water back on and check for any leaks. Be sure to monitor it for at least 10 minutes. If you detect any water leaking from either side of the filter, shut off the water again and try to tighten the connections until the leak stops.
Step Six: Enjoy Fresh Water
Once you've checked for leaks and everything appears to be in order, you can turn the water back on and enjoy fresh filtered water. Congratulations - you've successfully replaced your Whirlpool WP53-0918 FILTER-LIQUID!
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review