All Categories

This Front Load Washer Drive Belt causes your washer to spin properly during the washing cycle. If your washer pumps but does not spin or if the drum spins slowly, replacing t ...his part may alleviate these issues. This part attaches to the motor pulley and the transmission at the bottom of the appliance. While the the bottom of the washing machine is accessible, also consider replacing the motor pulley. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Washer Drive Belt• Tools Needed: Multi screwdriver, duct tape and standard pliers Read More Read Less

The Top Load Washer Timer controls the appliance’s wash cycle operations, including filling, soaking, washing, spinning and rinsing. If your washer is no longer progressing ...properly through each cycle, replacing this part may alleviate the issue. Use a flat-blade screwdriver to press the tabs to release the wiring harnesses from the broken timer. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Timer• Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

This Gas Oven Igniter Assembly will replace a broken bake or broil igniter in your gas range. You may need this part if the element no longer lights, or if the igniter of your ... oven glows for more than 90 seconds without lighting the gas flame – this indicates that the igniter is too weak to properly open the valve to allow the gas to feed through. Note that the igniter must glow white hot to properly light the oven; if it glows red or orange it is not functioning properly. Replacing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Also make sure to turn off the gas valve before the repair. Helpful Tip: You may need a Wire Splicer (item 3527618) to attach the connector from the old part to the new one so you can complete the installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Oven Igniter Assembly• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Drive Motor Assembly powers the drum of the appliance during operation. If your dryer's drum stops turning during the drying cycle, won't start at all, or the motor ...itself is loud, replacing this part may alleviate these issues. Note that the drive motor is frequently misdiagnosed; check more commonly defective parts before replacing the drive motor. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Item: Also consider replacing the Dryer Drum Belt (item WP33002535) at the same time you complete this repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drive Motor Assembly• Tools Needed: Multi screwdriver and socket with extension and ratchet Read More Read Less

This Washer Water Inlet Valve Assembly helps to control and balance the water temperature flowing into the washer tub by controlling the water flow into the washer. This assem ...bly includes the cold water inlet valve, hot water inlet valve, wire harness and housing. If your washer isn't filling with water as expected, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Washer Water Inlet Valve Assembly• Tools Needed: Multi screwdriver, 10" V-Jaw Tongue & Groove Pliers, tape, putty knife, standard pliers, nylon lanyard Read More Read Less

This Gas Range Spark Module creates the spark for lighting the gas for the range's surface burners. To access the part, you’ll need to remove the large panel on the rear of ...the range's console. Note that transferring the wires from the old part to the new part one at a time will help prevent incorrect installation. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure to turn the gas valve off before the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Burner Spark Module• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Range Sealed Gas Burner Head Assembly directs your oven's gas to the burner head. If the ceramic is cracked on your range or if the burner no longer ignites, replacing th ...is part may alleviate these issues. To install the new part, remove the old burner assembly by turning it counter clockwise by hand. If you are unable to loosen the old burner by hand, using a strap wrench may help. When you remove the ground and the spark wires from the old burner head, make sure they don't fall back into the range top. Turn the new burner head clockwise to lock when replacing. Replacing this part will require no disassembly or repair experience. You must unplug the appliance or shut off the house circuit breaker before installing. Also turn off the gas supply that's connected to your range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Sealed Gas Burner Assembly• No tools required for installation Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Temperature Sensor• Tools Needed: Multi screwdriver Read More Read Less

This Range Surface Burner Spark Module produces sparks that ignite the top gas burners on your range. If one or more of your top burners won't spark, replacing the module may ...alleviate this issue. This kit includes the (1) module, (1) mounting bracket, (2) connectors, (1) Phillips screw. The terminals supplied should not be used if they are different in size than the current terminals. To access the part, you'll remove the back panel of your range. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Surface Burner Spark Module Kit• Tools Needed: Multi screwdriver, needle nose pliers, 1/4" nut driver Read More Read Less