Maytag Appliance

This Dryer Heating Element is a replacement part that generates heat for drying your clothes. Be sure to check the thermal fuse on dryer before replacing the heating element. ...This is a 240 volt, 5400 watt heating element, and has 5/16" terminals. If your dryer isn't heating as expected, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Heating Element• Tools Needed: Multi screwdriver Read More Read Less

This Range Broil Element is a replacement part with 1/4" push-on wire terminals that provides constant heat to the broiler when cooking. If your broiler does not heat up prope ...rly, replacing this part may alleviate the issue. Replacing the element will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require additional steps during the installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Broil Element• Tools Needed: Multi screwdriver Read More Read Less

The Front Load Dryer Heating Element Kit generates heat in the appliance during the drying cycle. If your dryer isn’t heating properly, replacing this part may alleviate the ... issue. In order to access the part, you'll remove the back panel from the dryer. Installing the element kit will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Front Load Dryer Heating Element Kit• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Heating Element is a replacement part for heating element coils that short out, causing your dryer to no longer produce the heat necessary to dry your clothes. If yo ...ur dryer is not heating, replacing this part may alleviate the issue. This dryer heating element includes the thermostat, thermal fuse, and wires. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker before installing this part. Helpful Tip: The heating element and many other parts can be tested using a volt/ohm meter.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Heating Element• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Heating Element Wire Connector may need to be replaced if your dryer takes too long to dry your clothes or if your dryer is no longer producing heat. To start this r ...epair, pull the dryer away from the wall to access the back panel and remove the 9 screws holding the panel in place. Remove the wire from the heating block terminal and use your wire cutters to cut off the end of the wire near the terminal. The remove about a 1/4" of insulation from the end of the wire. Then you'll connect the new wire with the new nut to the existing wire. This kit Includes (1) wire with terminal and (1) wire nut. (2) ire connectors. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool: 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Dryer Heating Element Wire Connector Kit• Tools Needed: 1/4" nut driver, wire splicing tool, wire cutters Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.