KitchenAid Parts

This Electric Oven Upper Bake Element is a replacement part for the upper oven heating element that provides constant heat when cooking. If your oven does not bake properly, c ...heck to see if there is a burned-out section of the element and replace if needed. Installing the new element will require basic hand tools, some disassembly of the oven and novice repair experience. Remember to unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require addition steps during the installation process.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Oven Upper Bake Element•  Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Gas Range Surface Burner Igniter Clip holds the surface burner igniter in place. If the existing clip in your appliance is broken and no longer holding the igniter properl ...y, replacing this part may alleviate the issue. To access the part, remove your burner grates, burners and burner caps. Then remove the burner screws. Use a putty knife under the stove top to release the locking clips holding it in place and then lift up the top of the range. Each clip is sold separately. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Range Surface Burner Igniter Clip•  Tools Needed: Multi screwdriver, channel locks, needle nose pliers, putty knife Read More Read Less

The Range Surface Control Knob allows you to control the size of the flame coming from your cooktop burner. This stainless steel knob is approximately 2" in diameter and is so ...ld individually. Replacing this part will require no disassembly or repair experience.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Range Surface Control Knob•  No tools required for installation Read More Read Less

This Electric Range Oven Door Hinge allows the door of your oven to close properly and ensures it will safely remain open at an angle during use. Note that two hinges are used ... per oven; hinges are sold separately. This stainless-steel replacement part can be used for the left or right side. Replacing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the oven before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Electric Range Oven Door Hinge•  Tools Needed: Multi screwdriver Read More Read Less

This Built-in Oven Door Hinge allows the door of your wall oven to close properly and ensures it will safely remain open at an angle during use. Note that two hinges are used ...per oven; hinges are sold separately. This stainless-steel replacement part is designed to be used specifically with black stainless models. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Built-in Oven Door Hinge•  Tools Needed: Multi screwdriver Read More Read Less

The Electric Range Surface Burner Control Switch operates an 8" surface element, turning it off and on and regulating the heat intensity. If your element remains at high heat ...or doesn’t turn on at all, replacing this part may alleviate these issues. This surface burner control switch (also called the infinite switch) has a figure eight shaped shaft and measures 8.9 - 11 amp. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Electric Range Surface Burner Control Switch•  Tools Needed: Multi screwdriver Read More Read Less

The Range Temperature Sensor measures the oven temperature. If your oven isn't holding the correct temperature, replacing this part may alleviate the issue. Remove the rear ac ...cess panel to access the old sensor. Depress the tab to disconnect the sensor wire connector. unscrew the sensor mounting screw and pull out the old sensor. Insert the new sensor into the hole of the rear panel and replace the mounting screw to secure. Reconnect the wire connector and secure the access panel back into place. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing. Also make sure to shut off the gas.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Range Temperature Sensor•  Tools Needed: Multi screwdriver Read More Read Less

This Dual Oven Sensor monitors the temperature inside the lower oven compartment and relays the information to the main control board. If your lower oven isn’t heating prope ...rly, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dual Oven Sensor•  Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.