Amana Appliance Parts

The Range Bake Igniter glows white-hot to heat properly, and lives behind the access panel at the rear of your oven. If the igniter in your oven is glowing red or orange, or n ...ot glowing at all, it may be weak and needs to be replaced. The new igniter may not have connections attached to its wire ends, so you'll have to cut the connections off of the old igniter, strip the wires, and use the included wire nuts with the new igniter. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You should unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn the gas valve off before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Range Bake Igniter•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Front Load Washer Drive Belt causes your washer’s tub to spin properly during the cleaning cycle. If your washer pumps but does not spin or if the drum spins slowly, re ...placing this part may alleviate the issue. To access this part, you'll need to remove the hose and back panel of the machine. The belt measures 48-in. L x 11/16-in. W. Replacing this part will require basic hand tools, some disassembly of the washer and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn off the hot and cold water supplies to your washer. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Front Load Washer Drive Belt•  Tools Needed: Multi screwdriver, putty knife, pliers, towel Read More Read Less

The Top Load Washer Tub to Pump Hose stretches from the lower tub into the drain pump and helps removes waste water from the appliance during operation. This part includes (1) ... drain hose and (2) clamps. Installing this part will require basic hand tools, some disassembly of the washing machine and novice repair experience. You must unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner* (item W10501250) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Tub to Pump Hose•  Tools Needed: Multi screwdriver and putty knife (certain models) Read More Read Less

This Front Load Washer Drum Baffle Kit includes 3 baffles and 3 screws. The baffles are installed on the inside of the washer drum, and tumble the clothes in the washer. If th ...e baffles are loose or damaged, they may need to be replaced. To access the part, remove the top panel of the washer. If your specific model has screws, be sure to remove them with a magnetic tip screwdriver so they don't get lost inside the machine. Replacing this part may require specialized tools, complicated disassembly of the appliance, and repair experience. Please remember to unplug the washer or shut off the house circuit breaker for the appliance before installing this part. Also be sure to shut off your hot and cold water supplies.Recommended parts: Screw (item #697027 ) and Single Drum baffle (item #1059587) from parts.com.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Front Load Washer Drum Baffle Kit•  Tools Needed: Specialized Tools Read More Read Less

This Front Load Washer Shock Absorber absorbs the vibrations and movements of the outer washer tub. Your washer has 4 shock absorbers – 2 in the back and 2 in the front. If ...your tub is shaking while in cycle, replacing this part may alleviate the issue. You'll remove the hose and the back panel behind the machine to access this part. Turn the old shock absorber 90 degrees on the top and bottom to release it from the appliance. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Front Load Washer Shock Absorber•  Tools Needed: Multi screwdriver, channel locks, pliers Read More Read Less

This Top Load Washer Water Inlet Valve opens to allow water to enter the washing machine. The attaching solenoids on the valve open and close according to the desired temperat ...ure, or amount of water needed. If your washer won't stop filling with water, won't produce cold or hot water, won't fill at all, or is leaking, replacing the inlet valve may alleviate these issues.This inlet valve has 4 terminals and is located at the back of the machine. To access the part, you'll need to separate the washer cabinet from the washer and disconnect the red and white wiring connectors from the old part. Recommended Item: Washer Fill Hose (item 8212487RP). Package of two 5' industrial braid hoses with pre-installed washers and straight ends. We recommend replacing washing machine inlet hoses after 5 years of use to reduce the risk of hose failure. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Top Load Washer Water Inlet Valve Assembly•  Tools Needed: Multi screwdriver, needle-nose pliers Read More Read Less

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the part may alleviate these issues. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Range Surface Igniter•  Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This Washing Machine Drain Hose measures 8' L and drains the water properly during your washer's rinse cycle. This universal drain hose is compatible with several washing mach ...ine brands and will be needed if more than the standard distance exists between the washer and the drain; check your model number to confirm compatibility. Helpful Tip: This kit also includes a 1-1/2" D clamp, but the hose itself is -1/4" diameter. Therefore you may also need to order a 1-1/4" clamp separately to use this part. Installing this accessory will require basic hand tools and novice repair experience. You must unplug the washing machine or shut off the house circuit breaker for the appliance before installing this part. Also make sure you turn off your hot and cold water supplies.Part Specification•  This product is a Factory Certified Accessory. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  Package contains (1) Washing Machine Drain Hose•  Tools Needed: Standard pliers Read More Read Less

The Whirlpool 207843 LIP SEAL REPAIR KIT is your perfect solution to repair any damaged lip seals on your appliance. Don’t be stuck with a leaky, inefficient machine - this ...repair kit will help you fix the problem in no time. It comes with everything you need for a successful repair, including an O-ring, lip seal, and instruction sheet. With a durable design, this repair kit ensures that your appliance runs as smoothly and efficiently as possible. Get your problems solved quickly with the Whirlpool 207843 LIP SEAL REPAIR KIT! We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs! Read More Read Less

The Dryer Heating Element is a replacement part for the heating element coils that dry your clothes. If your dryer is not heating as expected, replacing this part may alleviat ...e the issue. First check for a blown thermal fuse on the blower housing before replacing the heating element. To access the part, remove the back panel from your dryer. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Dryer Heating Element•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less