Online Sale!
100% Guaranteed Genuine Parts
WP9760771 Whirlpool Electric Oven Broil Element
This Range Broil Heating Element is a replacement part that provides constant heat to the broiler when cooking. If your broiler does not heat up properly, the element has likely shorted out and will need to be replaced. Reuse the existing support bracket for the element if your oven has one when installing this part. Replacing the element will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require additional steps during the installation
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Range Broil Heating Element
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Range Broil Heating Element
• Tools Needed: Multi screwdriver
Weight : 9.163300 lbs
Dimension : 20.984200 x 17.519600 x 3.464500
Compatible Brands
About this product
This Range Broil Heating Element is a replacement part that provides constant heat to the broiler when cooking. If your broiler does not heat up properly, the element has likely shorted out and will need to be replaced. Reuse the existing support bracket for the element if your oven has one when installing this part. Replacing the element will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require additional steps during the installation
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Range Broil Heating Element
• Tools Needed: Multi screwdriver
Part Specification
• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications
• This product is a replacement part
• Package contains (1) Range Broil Heating Element
• Tools Needed: Multi screwdriver
Weight : 9.163300 lbs
Dimension : 20.984200 x 17.519600 x 3.464500
The following parts are replaced by this product
- 4456103
- 9760771
No more associated models for this part.
DIY Instructions on Replacing the Whirlpool WP9760771 ELMNT-BROLMNT
1. Turn off the power to the appliance. Unplug the refrigerator and shut off the water supply.
2. Remove the upper front panel. Locate the two screws at the top of the control panel and remove them. Gently pull the panel away from the refrigerator.
3. Disconnect the wire harness from the ELMNT-BROLMNT by pulling gently on the connector.
4. Remove the mounting screws that hold the ELMNT-BROLMNT to the control panel.
5. Install the new part, reverse the steps above to reinstall the refrigerator control panel and reconnect the wires.
6. Plug the refrigerator back in, turn the water supply back on and turn the power back on.
7. Run a test cycle to ensure the part is working correctly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
1. Turn off the power to the appliance. Unplug the refrigerator and shut off the water supply.
2. Remove the upper front panel. Locate the two screws at the top of the control panel and remove them. Gently pull the panel away from the refrigerator.
3. Disconnect the wire harness from the ELMNT-BROLMNT by pulling gently on the connector.
4. Remove the mounting screws that hold the ELMNT-BROLMNT to the control panel.
5. Install the new part, reverse the steps above to reinstall the refrigerator control panel and reconnect the wires.
6. Plug the refrigerator back in, turn the water supply back on and turn the power back on.
7. Run a test cycle to ensure the part is working correctly.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Write Your Own Review