WD12X10109 GE Dishwasher Fine Filter Assembly
Fine filter assembly works with some GE, and Hotpoint models of dishwashers.
Weight : 2.529100 lbs
Dimension : 14.000000 x 9.300000 x 2.700000
Product Details
Reviews
Replaces Parts
Installation Instructions
Compatible Models
Compatible Brands
Fine filter assembly works with some GE, and Hotpoint models of dishwashers.
Weight : 2.529100 lbs
Dimension : 14.000000 x 9.300000 x 2.700000
Write Your Own Review
The following parts are replaced by this product
- WD12X10050
How to Replace the WD12X10109 GE Dishwasher Fine Filter Assembly
Replacing the WD12X10109 GE dishwasher fine filter assembly is a relatively simple DIY project that can be completed quickly with few tools and basic technical skills. This guide will walk you through step-by-step instructions on how to perform this task in a safe and effective manner.
Step 1: Going Prepare the Dishwasher
Prior to disassembling your dishwasher, you should make sure that all power has been turned off. Unplug the electrical cord from the wall outlet and turn off the circuit breaker that controls the dishwasher.
Once the power has been turned off, open the door of the dishwasher and remove any dishes or utensils that are stored inside.
Step 2: Removing the Filter
The filter assembly is located in the lower portion of the dishwasher tub. To access the filter assembly, you will need to locate the screws that secure the bottom panel of the dishwasher to the sides of the tub. Using a Phillips-head screwdriver, loosen and remove the screws that are securing the bottom panel.
Once the screws have been removed, the bottom panel of the dishwasher can be carefully pulled away from the sides of the tub. Locate the filter assembly which is typically near the center of the opening.
Using a pair of pliers, loosen the mounting screws that secure the filter to the dishwasher frame and carefully pull out the filter assembly.
Step 3: Cleaning the Dishwasher Tub
vacuuming the interior surface of the dishwasher tub. This will ensure that any food particles or dirt that has accumulated in the tub is removed.
Step 4: Replacing the Filter Assembly
Carefully lift the new filter assembly into place in the dishwasher and tighten the mounting screws to secure it in place.
Replace the bottom panel of the dishwasher and secure it to the sides of the tub with the screws removed earlier.
Step 5: Testing the Dishwasher
Plug the electrical cord back into the wall outlet and turn the circuit breaker back on. Close the door of the dishwasher and start a short cycle to test that the filter assembly has been correctly replaced.
Once the short cycle has completed, open the door and inspect the interior of the dishwasher to ensure that the filter has been correctly installed and that the dishwasher is functioning properly.
Conclusion
Replacing the WD12X10109 GE dishwasher fine filter assembly is a straightforward and cost efficient DIY project that can be completed quickly with minimal effort. By following the steps outlined in this guide, you will be able to replace your filter assembly safely and efficiently.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Replacing the WD12X10109 GE dishwasher fine filter assembly is a relatively simple DIY project that can be completed quickly with few tools and basic technical skills. This guide will walk you through step-by-step instructions on how to perform this task in a safe and effective manner.
Step 1: Going Prepare the Dishwasher
Prior to disassembling your dishwasher, you should make sure that all power has been turned off. Unplug the electrical cord from the wall outlet and turn off the circuit breaker that controls the dishwasher.
Once the power has been turned off, open the door of the dishwasher and remove any dishes or utensils that are stored inside.
Step 2: Removing the Filter
The filter assembly is located in the lower portion of the dishwasher tub. To access the filter assembly, you will need to locate the screws that secure the bottom panel of the dishwasher to the sides of the tub. Using a Phillips-head screwdriver, loosen and remove the screws that are securing the bottom panel.
Once the screws have been removed, the bottom panel of the dishwasher can be carefully pulled away from the sides of the tub. Locate the filter assembly which is typically near the center of the opening.
Using a pair of pliers, loosen the mounting screws that secure the filter to the dishwasher frame and carefully pull out the filter assembly.
Step 3: Cleaning the Dishwasher Tub
vacuuming the interior surface of the dishwasher tub. This will ensure that any food particles or dirt that has accumulated in the tub is removed.
Step 4: Replacing the Filter Assembly
Carefully lift the new filter assembly into place in the dishwasher and tighten the mounting screws to secure it in place.
Replace the bottom panel of the dishwasher and secure it to the sides of the tub with the screws removed earlier.
Step 5: Testing the Dishwasher
Plug the electrical cord back into the wall outlet and turn the circuit breaker back on. Close the door of the dishwasher and start a short cycle to test that the filter assembly has been correctly replaced.
Once the short cycle has completed, open the door and inspect the interior of the dishwasher to ensure that the filter has been correctly installed and that the dishwasher is functioning properly.
Conclusion
Replacing the WD12X10109 GE dishwasher fine filter assembly is a straightforward and cost efficient DIY project that can be completed quickly with minimal effort. By following the steps outlined in this guide, you will be able to replace your filter assembly safely and efficiently.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
