Magic Chef Appliance Parts

This Range Sealed Gas Burner Head Assembly directs your oven's gas to the burner head. If the ceramic is cracked on your range or if the burner no longer ignites, replacing th ...is part may alleviate these issues. To install the new part, remove the old burner assembly by turning it counter clockwise by hand. If you are unable to loosen the old burner by hand, using a strap wrench may help. When you remove the ground and the spark wires from the old burner head, make sure they don't fall back into the range top. Turn the new burner head clockwise to lock when replacing. Replacing this part will require no disassembly or repair experience. You must unplug the appliance or shut off the house circuit breaker before installing. Also turn off the gas supply that's connected to your range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Sealed Gas Burner Assembly• No tools required for installation Read More Read Less

The Dryer Motor Pulley rotates to turn the dryer’s drum belt, which spins the drum during the drying cycle. If your dryer makes a persistent squealing sound during operation ..., the drum rotates intermittently but clunks or the drum does not rotate at all, you may be able to alleviate these issues by replacing this part. Installing the motor pulley will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Motor Pulley• Tools Needed: Multi screwdriver, adjustable wrench Read More Read Less

This Top Load Washer Drain Pump is located at the bottom of the appliance and removes water during the drain portion of the wash cycle. If your washer doesn’t drain properly ..., replacing this part may alleviate this issue. This part may also be needed if water drips out of the tub during use or there’s an unpleasant noise during operation. Note that this pump has been redesigned and may look different than the current part in your appliance; the new pump attaches directly to the base of the washer and no longer requires a mounting plate. To access the part, start by removing the front access panel of the washer. You'll then remove the hoses attached to the pump (be sure to place some towels down to catch any water). Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you turn off the hot and cold water supplies. Helpful Tip: We also recommend using affresh® Washing Machine Cleaner Tablets* (item W10135699) once a month to help reduce odor-causing residue that can build up in your washing machine's drain without proper care. *affresh® brand products are owned and distributed by Whirlpool Corporation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Top Load Washer Drain Pump• Tools Needed: Multi screwdriver, needle-nose pliers and putty knife Read More Read Less

This Gas Oven Vertical Igniter Kit is also referred to as a glow bar. You may need this part if the element itself shorted out, or if the igniter of your oven glows for more t ...han 90 seconds without lighting the gas flame – this may indicate that the igniter is too weak to properly open the valve to allow the gas to feed through. The igniter must glow white hot to properly light the oven; if it glows red or orange replacing it may alleviate these issues. To access the part, pull the oven door off its hinges to remove it, and remove the racks from the oven. The remove the screws holding the bottom panel of the oven in. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also turn off the gas supply that's connected to your oven.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Oven Vertical Igniter Kit• Tools Needed: 1/4" nut driver and 5/16" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Range Surface Burner Spark Module produces sparks that ignite the top gas burners on your range. If one or more of your top burners won't spark, replacing the module may ...alleviate this issue. This kit includes the (1) module, (1) mounting bracket, (2) connectors, (1) Phillips screw. The terminals supplied should not be used if they are different in size than the current terminals. To access the part, you'll remove the back panel of your range. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Surface Burner Spark Module Kit• Tools Needed: Multi screwdriver, needle nose pliers, 1/4" nut driver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

Whirlpool Jenn-Air KitchenAid Maytag Roper Admiral Sears Kenmore Norge Magic Chef Amana Refrigerator Electronic Control Board W10789107We are a Factory Authorized Parts Distri ...butor for Whirlpool Maytag. Trust us for all of your Whirlpool Maytag appliance parts and accessories needs. Read More Read Less