EWC1201-12 Avanti Main PCB
Part #: AVP EWC1201-12
The Avanti EWC1201-12 MAIN PCB is an essential component for your Avanti product. This robust PCB is designed for long-term use and reliable operation, ensuring that your product will work for years to come. This board is easy to install and can easily be integrated into your existing setup. With intelligent circuitry, this PCB offers efficient energy usage and enhanced control over operations. The EWC1201-12 is designed to meet the highest quality standards, so you can trust it to work reliably, no matter the application. With superior performance and reliability, this main PCB is the perfect choice for your Avanti product. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
The Avanti EWC1201-12 MAIN PCB is an essential component for your Avanti product. This robust PCB is designed for long-term use and reliable operation, ensuring that your product will work for years to come. This board is easy to install and can easily be integrated into your existing setup. With intelligent circuitry, this PCB offers efficient energy usage and enhanced control over operations. The EWC1201-12 is designed to meet the highest quality standards, so you can trust it to work reliably, no matter the application. With superior performance and reliability, this main PCB is the perfect choice for your Avanti product. We're your #1 source for genuine OEM appliance parts. Contact us for further questions as well as any other appliance parts needs!
Write Your Own Review
Replacing the Avanti Products EWC1201-12 Main PCB
Introduction
Replacing the main Printed Circuit Board (PCB) on the Avanti Products EWC1201-12 is a relatively easy process, requiring only a few simple tools and basic knowledge of electronics. This DIY guide will walk you through the process of replacing the main Printed Circuit Board step-by-step.
Tools & Materials
Before you start, make sure you have the following tools and supplies:
• Anti-static Wrist Strap
• Phillips-head screwdriver
• A replacement Avanti Products EWC1201-12 Main PCB
Instructions:
1. Power off the appliance, disconnect it from any power source and unplug all cables.
2. Put on the Anti-static wrist strap to protect against electrostatic discharge.
3. Using the Phillips-head screwdriver, remove the screws holding the back panel in place.
4. Carefully take off the back panel and locate the main Printed Circuit Board (PCB).
5. Disconnect all cables connected to the board.
6. Remove the screws holding the board in place and lift the board out of the appliance.
7. Place the replacement board in the same position as the old one and secure it with the screws.
8. Reconnect all the cables connected to the board.
9. Re-install the back panel and secure it with the screws.
10. Connect the appliance back to the power source and power on.
Conclusion
Replacing the main Printed Circuit Board on the Avanti Products EWC1201-12 is a relatively simple process that can be completed in a few easy steps. Always take extra precaution, turn off the power before attempting to open the case and use an anti-static wrist strap when handling electronic parts.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
Introduction
Replacing the main Printed Circuit Board (PCB) on the Avanti Products EWC1201-12 is a relatively easy process, requiring only a few simple tools and basic knowledge of electronics. This DIY guide will walk you through the process of replacing the main Printed Circuit Board step-by-step.
Tools & Materials
Before you start, make sure you have the following tools and supplies:
• Anti-static Wrist Strap
• Phillips-head screwdriver
• A replacement Avanti Products EWC1201-12 Main PCB
Instructions:
1. Power off the appliance, disconnect it from any power source and unplug all cables.
2. Put on the Anti-static wrist strap to protect against electrostatic discharge.
3. Using the Phillips-head screwdriver, remove the screws holding the back panel in place.
4. Carefully take off the back panel and locate the main Printed Circuit Board (PCB).
5. Disconnect all cables connected to the board.
6. Remove the screws holding the board in place and lift the board out of the appliance.
7. Place the replacement board in the same position as the old one and secure it with the screws.
8. Reconnect all the cables connected to the board.
9. Re-install the back panel and secure it with the screws.
10. Connect the appliance back to the power source and power on.
Conclusion
Replacing the main Printed Circuit Board on the Avanti Products EWC1201-12 is a relatively simple process that can be completed in a few easy steps. Always take extra precaution, turn off the power before attempting to open the case and use an anti-static wrist strap when handling electronic parts.
Please keep in mind, these instructions are for general guidance and should always be used in conjunction with the manufacturer's manual, if available.
No more associated models for this part.
