All Categories

This Trash Compactor On/Off Switch also known as the rotary or start switch, controls the electrical power that reaches the appliance. If your trash compactor’s current swit ...ch is broken or malfunctioning, you can replace it with this part. Note that a multimeter can be used to test the current switch for continuity before you replace the part. Installing this part will require basic hand tools, some some disassembly of the compactor and novice repair experience. You must unplug the compactor or shut off the house circuit breaker for the appliance before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Trash Compactor On/Off Switch•  Tools Needed: Multi screwdriver Read More Read Less

The Gas Dryer Igniter lights the gas in your dryer. If your dryer is no longer supplying heat, this part may be damaged or cracked and may need to be replaced. To access the p ...art, lift the top of the dryer by releasing the spring clips from the top panel with a putty knife. Then remove the door switch wires and the screws that release the front panel. Next, simply loosen the screw that holds in the igniter to remove it. Please note that the bracket is no longer included with this part. If your original igniter was round, also order bracket (item 37001309). Replacing this assembly will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Note that you cannot touch the grey part of the igniter; only handle the igniter by its white plastic covering.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Dryer Igniter Kit•  Tools Needed: Multi screwdriver, putty knife, 5/16" wrench Read More Read Less

The Range Bake Igniter glows white-hot to heat properly, and lives behind the access panel at the rear of your oven. If the igniter in your oven is glowing red or orange, or n ...ot glowing at all, it may be weak and needs to be replaced. The new igniter may not have connections attached to its wire ends, so you'll have to cut the connections off of the old igniter, strip the wires, and use the included wire nuts with the new igniter. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You should unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn the gas valve off before installing this part.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Range Bake Igniter•  Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the part may alleviate these issues. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification•  This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications•  This product is a replacement part•  Package contains (1) Gas Range Surface Igniter•  Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.