Whirlpool Appliance

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Electric Range Coil Surface Element is a 4-turn, 6" D, 1500-W plug-in style heating element. If the surface burner of your appliance no longer heats up, you may be able to ... alleviate the issue by replacing this part. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Recommended Items: If the element's terminals are corroded, you can replace them with the Element Receptacle and Wire Kit (item 330031). If more than one of your appliance’s elements are no longer working, consider purchasing the complete Coil Surface Element Kit (item 4392061). If needed, the matching 6" element (item WP660532) is also sold separately. If the stainless-steel Burner Drip Bowls of your appliance are discolored or dented, you can replace them with item W10278125.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Coil Surface Element• No tools required for installation Read More Read Less

The Dryer Heating Element Wire Connector may need to be replaced if your dryer takes too long to dry your clothes or if your dryer is no longer producing heat. To start this r ...epair, pull the dryer away from the wall to access the back panel and remove the 9 screws holding the panel in place. Remove the wire from the heating block terminal and use your wire cutters to cut off the end of the wire near the terminal. The remove about a 1/4" of insulation from the end of the wire. Then you'll connect the new wire with the new nut to the existing wire. This kit Includes (1) wire with terminal and (1) wire nut. (2) ire connectors. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Item: Wire Splicing Tool: 8-1/4". This stripper specializes in stripping and cutting wire. This tool is designed with a lean nose for pulling and looping wire and equipped with precision ground cutters.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• Package contains (1) Dryer Heating Element Wire Connector Kit• Tools Needed: 1/4" nut driver, wire splicing tool, wire cutters Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Electric Range Dual Radiant Element supplies heat to the left-front cooking area on top of the range. This dual element allows you to adjust the size of the burner you wan ...t to use to match the width of your pots and pans. Elements are sold separately. Installing this part will require basic hand tools, some disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: Take a digital photo or make a note of the current wiring before removing the existing part to aid with installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Dual Radiant Element• Tools Needed: Multi screwdriver and a sturdy 12" wooden stick to support the cooktop during the repair Read More Read Less

This Electric Range Broil Element is located at the top of the oven and provides constant heat to the broiler when cooking. If your broiler does not heat up properly, the elem ...ent may be shorted out and will need to be replaced. To access the existing part, you'll need to remove the oven racks. The element is attached to the top of the oven with a bracket and screws. Replacing the element will require basic hand tools or repair experience. Remember to unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Helpful Tip: Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require addition steps during installation, including removal of the rear panel of the appliance.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Broil Element• Tools Needed: Multi screwdriver Read More Read Less

This Range Broil Element is a replacement part with 1/4" push-on wire terminals that provides constant heat to the broiler when cooking. If your broiler does not heat up prope ...rly, the element has likely shorted out and will need to be replaced. Reuse the existing support bracket for the element if your oven has one when installing this part. Replacing the element will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require additional steps during the installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Broil Element• Tools Needed: Phillips-Head screwdriver Read More Read Less

This Electric Range Broil Element is a 3-loop replacement part with push-on wire terminals that provides constant heat to the broiler when cooking. If your broiler does not he ...at up properly, the element may have shorted out and need replacement. Replacing the element will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require addition steps during the installation process.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Broil Element• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Electric Range Coil Surface Element is a 6" D, 4-turn delta base heating element with looped terminal ends. This element features easy-to-install “plug in” style termi ...nals and is compatible with many electric oven makes and models. If your stove's burner no longer heats up, replacing this part may alleviate the issue. Installing this part will require no tools, disassembly or repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing this part. Recommended Items: If the range's terminals are corroded, you can replace them with the Element Receptacle and Wire Kit (item 12001676). Stainless-steel Burner Drip Bowls (item 715877) are available if the ones on your range need to be replaced.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Coil Surface Element• No tools required for installation Read More Read Less