Norge Appliance Parts

This Dishwasher Access Panel Retainer, Black, holds the protective panel along the bottom of the dishwasher in place. If one or more of the appliance’s plastic retainers are ... cracked or broken, you can easily replace them with this part. Installing this part will require basic hand tools and no disassembly or repair experience.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dishwasher Access Panel Retainer, Black• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Drum Roller Kit supports the rear of the appliance’s drum to help it maintain quiet and balanced spinning during the drying cycle. If your dryer’s drum is moving ... up and down during operating, replacing this part may alleviate the issue. The drum bearings are self-lubricating; it is not necessary to lubricate them yourself. The kit includes (2) drum rollers, (4) tri rings, (1) retaining washer and installation instructions. Helpful Tip: While the dryer is disassembled, also consider replacing the right (item WPW10359269) and left (item WPW10359270) drum roller axles. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drum Roller Kit• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Dryer Felt Seal encloses the drum in the appliance to prevent air from escaping during the drying cycle. If the seal in your dryer is worn out or damaged, you may notice b ...rown stains on your clothes after use. This is not caused by oil from the dryer, the clothes are most likely getting pinched in the drum’s holes during tumbling due to a faulty seal. As the felt seal wears out and compresses over time, it can also cause hot air to escape the drum, making the drying cycle less effective and efficient. This replacement part includes a tube of adhesive to complete the repair. Installing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Felt Seal• Tools Needed: Multi screwdriver, putty knife Read More Read Less

This Range Broil Element is a replacement part with 1/4" push-on wire terminals that provides constant heat to the broiler when cooking. If your broiler does not heat up prope ...rly, replacing this part may alleviate the issue. Reuse the existing support bracket for the element if your oven has one when installing this part. Replacing the element will require basic hand tools, some disassembly of the oven and novice repair experience. You must unplug the oven or shut off the house circuit breaker for the appliance before installing this part. Be mindful not to let the wires connected to the current part fall back inside the oven when you disconnect them; retrieval of the wires will require additional steps during the installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Broil Element• Tools Needed: Phillips-Head screwdriver or power driver Read More Read Less

W11185686 Whirlpool Ice Bucket Assembly

The SxS Refrigerator Water Inlet Valve allows water to enter the refrigerator’s water dispenser and ice maker. The package includes (1) inlet water valve, (2) screws, (1) br ...acket and installation instructions. If one of the solenoids in the original unit is bad, it will prevent water from entering the ice maker and dispenser. If the icemaker of your appliance stops making ice, no water flows from the dispenser or it flows constantly, or if you notice water at the bottom of the fresh food compartment, the water inlet valve could be malfunctioning and need to be replaced. Installing this part will require basic hand tools, some disassembly of the refrigerator and intermediate repair experience. You must unplug the refrigerator or shut off the house circuit breaker for the appliance before installing this part. Also turn off the refrigerator’s water supply before you begin. Helpful Tip: We do not recommend disassembling your appliance’s current water inlet valve to clean it due to the risk of failure after the repair.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Refrigerator Water Inlet Valve Assembly• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

The Electric Range Surface Burner Control Switch is a replacement part that operates the appliance’s surface element, turning it off and on and regulating the heat intensity .... If your element remains at high heat or doesn’t turn on at all, the surface element switch (also called the infinite switch) may be damaged and need replacement. Installing this part will require basic hand tools, minor disassembly of the range and novice repair experience. Remember to unplug the range or shut off the house circuit breaker for the appliance before installing this item. Helpful Tip: Taking a digital photograph of the current wiring connections before replacing this part is advisable to aid with proper installation.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Electric Range Surface Burner Control Switch• Tools Needed: Multi screwdriver Read More Read Less