Amana Appliance Parts

The Dryer Drive Belt wraps around the motor and pulley and rotates the belt and the belt tumbles the drum. If the drum of your appliance isn't operating as expected, replacing ... this part may alleviate the issue. To access the part, first lift up the lint screen cover and remove the two screws. If you have the type of lint screen that has the cover built in, just pull it out and then remove the screws. Next, take a putty knife around the edge of the top of your dryer and find the release clips--press these in to release the top of the dryer so you can swing it open. The front panel also needs to be removed to replace the belt. This long slender belt measures 93-3/8" L x 3/8" W and features 5 ridges. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Drum Belt• Tools Needed: Flat-blade screwdriver, putty knife, 5/16" nut driver Read More Read Less

The Range Bake Igniter glows white-hot to heat properly, and lives behind the access panel at the rear of your oven. If the igniter in your oven is glowing red or orange, or n ...ot glowing at all, it may be weak and needs to be replaced. The new igniter may not have connections attached to its wire ends, so you'll have to cut the connections off of the old igniter, strip the wires, and use the included wire nuts with the new igniter. Installing this part will require basic hand tools, some disassembly of the oven and novice repair experience. You should unplug the appliance or shut off the house circuit breaker for the appliance before installing this part. Also be sure to turn the gas valve off before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Range Bake Igniter• Tools Needed: Multi screwdriver, wire splicing tool Read More Read Less

This Gas Range Surface Igniter provides spark to the burner to ignite the gas and initiate the cooking process. This igniter features a spark electrode with a male spade conne ...ction. If your range’s igniter is no longer providing a spark to light the burner, the wire may be shorted out or the porcelain casing may be cracked. Replacing the part may alleviate these issues. Be mindful not to lose the two burner wires inside the appliance when you detach them from the old burner head. To install the new part, simply insert it into the burner head and secure it with two screws. Replacing this part will require basic hand tools, some disassembly of the range and novice repair experience. You must unplug the range or shut off the house circuit breaker for the appliance before installing this part. Also make sure you shut off the gas to the range.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Gas Range Surface Igniter• Tools Needed: Multi screwdriver, strap wrench Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This Dryer Thermal Cut Off Kit is a safety device designed to protect the dryer from overheating. A multimeter can be used to test the fuse. Always check the dryer venting whe ...n replacing a blown thermal fuse. To access the part, you'll need to remove the back panel of your dryer. This kit includes one thermal cut-off (360 degrees) and one hi-limit thermostat (250 degrees). If your dryer isn't heating as expected, replacing this part may alleviate the issue. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Thermal Cut Off Kit• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Idler Pulley Wheel Kit sits between the motor and the drum of the dryer, putting tension on the drive belt. If the idler wheel no longer spins inside your appliance, ... replacing this part may alleviate the issue. This kit comes with a tri-ring and washer. Replacing this part will require basic hand tools, some disassembly of the dryer and novice repair experience. You must unplug the dryer or shut off the house circuit breaker for the appliance before installing this part. Recommended Part: Consider replacing the Drive Belt (item #661570V) at the same time you complete this repair. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Idler Pulley Kit• Tools Needed: Multi screwdriver Read More Read Less

The Dryer Heating Element is a replacement part for heating element coils that short out, causing your dryer to no longer produce the heat necessary to dry your clothes. If yo ...ur dryer is not heating as expected, replacing this part may alleviate the issue. Note that we recommend first checking for a blown thermal fuse on the blower housing before replacing the heating element. Replacing this part will require basic hand tools, some disassembly of the appliance and novice repair experience. You must unplug the appliance or shut off the house circuit breaker before installing this part. Helpful Tip: The heating element and many other parts can be tested using a volt/ohm meter.Part Specification• This product is a Factory Certified Part. These three words represent quality parts and accessories designed specifically for your appliance. Time tested engineering that meets our strict quality specifications• This product is a replacement part• Package contains (1) Dryer Heating Element• Tools Needed: Multi screwdriver Read More Read Less

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.

This is a genuine OEM part that works for some models of Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper models.